![setool v0.9140 setool v0.9140](https://www.scitepress.org/Papers/2018/90058/pdf/bg4.png)
The last date to receive applicable service and support for the product as entitled by active service contracts or by warranty terms and conditions. The instrument was designed for temperature calibration. DO NOT use this instrument for any application other than calibration work. The last date to extend or renew a service contract for the product. ing power such as storage in a low humidity temperature chamber operat-ing at 50☌ for 4 hours or more.
Setool v0.9140 software#
The last-possible date a routine failure analysis may be performed to determine the cause of hardware product failure or defect.įor equipment and software that is not covered by a service-and-support contract, this is the last date to order a new service-and-support contract or add the equipment and/or software to an existing service-and-support contract. Actual ship date is dependent on lead time. The last-possible ship date that can be requested of Cisco and/or its contract manufacturers.
![setool v0.9140 setool v0.9140](https://www.scitepress.org/Papers/2018/90058/pdf/bg5.png)
The product is no longer for sale after this date. The last date to order the product through Cisco point-of-sale mechanisms. It is convenient for projects that will be attached or mounted at a 90 degree angle to any flat surface or T. And you know that the packing is good (and that the upper and lower ball is not stuck) then replace the inlet assembly.The date the document that announces the end of sale and end of life of a product is distributed to the general public. The 90 degree straight base connector is made of nylon and is used with a Quick Frame profile which has built-in ridges that bite into the fastener to create tension without the use of hardware.
Setool v0.9140 full#
The basic way to tell is if the pump is priming, but will not build up full pressure. So it is sometimes hard to tell when to replace the inlet assembly. A worn inlet will give you similar symptoms as a worn packing. 2: A inlet will eventually wear out and need replacing.
![setool v0.9140 setool v0.9140](https://ppid.diskominfo.jatengprov.go.id/wp-content/uploads/2021/10/Isu-Hoaks-17-Oktober-2021.png)
If it is lost this means the user took the assembly apart and lost the ball.) (Common part to loose is the ball, which the ball CAN NOT come out on its own.
Setool v0.9140 manual#
(Refer to the owner's manual for further instructions located on page 20 of the latest DSP/Apex owner's manual.) However please avoid taking the inlet apart for cleaning. If needed, you can remove the inlet assembly from the sprayer for further cleaning/inspecting. Note: The 9140/1420 models are not affected, you can use either the 0512215 or the 0516219 suction set with either the pusher inlet or the non pusher inlet. So if you are thinking about upgrading an older (non pusher) DSP/Apex sprayer (that has wheels) to the new style inlet you MUST purchase a new 0516278 Metal-Flex suction set as it is about พ" inch shorter. The New/Pusher Inlet is approximately พ" inch longer than the Old Style-Non Pusher Inlets. Cart models (wheeled), MUST use Metal-Flex suction set with New/Pusher Style Inlet.Meaning the Old Style-Non Pusher sprayers will accept the New/Pusher Inlets and the New/Pusher Sprayers will accept the Old Style-Non Pusher Inlets. This 0516292 New/Pusher style inlet is backwards compatible with 051222 Old Style-Non Pusher. The New/Pusher and Non Pusher Inlets are interchangeable.This inlet feature a "Pusher Stem" that allows a user to push/tap the lower ball without having to remove the suction set. This is the New/Pusher style inlet valve assembly that is included with DSP/Apex pumps listed in the above chart with build dates in late 20 onward. Fits the Following Airless Paint Sprayers